Advanced High-Pressure Die Casting Solution for EV Aluminum Battery Tray Components
2026-11-16 15:30
The rapid development of new energy vehicles pushes battery system design toward larger integrated structures to boost energy density and simplify assembly. The aluminum battery tray serves as the core load-bearing and protective part of the battery pack. It needs to withstand road vibration, impact load and long-term temperature cycling, while its flange sealing surface must maintain high flatness to prevent water and dust ingress. As a large-size thin-wall high-pressure die casting, the battery tray brings huge challenges to die casting manufacturers. Large projection area, irregular rib layout, uneven wall thickness and long solidification time easily trigger defects such as hot tearing, residual stress distortion, shrinkage porosity and flange surface depression. Traditional fixed-process parameters often lead to unstable yield and high post-machining scrap.
A die casting technical team in South China has developed a targeted integrated casting solution for such large battery tray parts. The scheme covers alloy optimization, gating system redesign, graded mold temperature control, process curve tuning and full-process quality monitoring. This news elaborates on the technical points and production application effects, following the same structure as previous articles.
1. Special Quality Risks of EV Aluminum Battery Trays
Different from small and medium-sized motor housings and heat sinks, EV battery trays are typical large thin-walled castings, usually with a projected area exceeding 0.8 ㎡ and main wall thickness between 2.0–3.0 mm. Reinforcing ribs are distributed unevenly across the tray body, and local bosses and connecting bases are thickened for bolt assembly. The drastic difference in wall thickness causes asynchronous solidification inside the die cavity.
The most troublesome defect is hot tearing. Hot tears form when the alloy is still in the brittle semi-solid state, and solidification shrinkage stress exceeds the tensile strength of the grain boundary. Cracks often appear at the transition positions between thick bosses and thin ribs. These tiny cracks are hard to detect by visual inspection and may expand under vehicle vibration, bringing serious safety hazards.
Residual stress and warpage are another major pain point. After ejection, uneven cooling speed between the rib side and flange side leads to inconsistent shrinkage. Even if the blank looks qualified, the part will deform after CNC machining, resulting in out-of-tolerance flatness of the sealing flange. Once flatness fails, the gasket cannot fit tightly, and the battery pack loses IP protection performance. Automotive customers usually require 100% CMM sampling inspection on key sealing zones and strict UT inspection for hot tearing.
Many foundries used to solve warpage simply by manual straightening. But forced straightening introduces new internal stress. Under alternating high and low temperature environments in vehicle operation, the part will rebound and deform again, so this method cannot meet long-term reliability requirements.
2. Aluminum Alloy Modification and Melt Purification Control
The foundation of stable casting quality starts from the molten aluminum itself. The team selected a specialized Al-Si alloy suitable for large thin-wall structural castings and adjusted the proportion of silicon, magnesium and iron. Low iron content is controlled to reduce brittle intermetallic phases that increase crack sensitivity, while appropriate strontium modification refines silicon grains to improve alloy plasticity and reduce the tendency of hot tearing.
Standardized melt treatment procedures are enforced in production. Rotary degassing removes dissolved hydrogen to reduce porosity risk. Ceramic foam filtration intercepts oxide slag and inclusions generated during melting and transfer. Each furnace is sampled for spectral composition testing. Melt temperature before entering the shot sleeve is kept within a narrow window. Too high melt temperature increases shrinkage stress and hot tearing risk; too low temperature causes cold shut and poor filling of far-end thin ribs.
Melt transfer is also optimized to avoid secondary oxidation. The launder is equipped with a covering agent, and the transfer path is shortened to reduce turbulence and slag entrapment. Stable melt quality greatly reduces random defects that are difficult to reproduce and troubleshoot in trial production.
3. Gating, Overflow and Venting Design Optimized for Large Cavity
For large battery trays, unreasonable gating system layout will cause disordered metal flow, early solidification of local thin walls and concentrated shrinkage stress. The team adopts multi-point sequential tangential gating, feeding molten aluminum from multiple positions along the tray’s edge. This design shortens the filling distance of the thin wall, keeps the flow front advancing steadily, and avoids severe turbulence and gas entrapment.
Multiple overflow pockets are set at the last filling ends of long ribs and flange corners. These overflows collect cold material, slag and residual gas. They also act as feeding reservoirs for hot spots to relieve shrinkage stress, which is critical for suppressing hot tearing at boss-rib transition zones. Venting slots are arranged at the parting line and overflow tails. The sealing of the mold parting surface is checked carefully to prevent air leakage, which would destroy the exhaust effect.
All filling and solidification behaviour is simulated via CAE simulation in advance. Engineers compare different gating schemes, predict the position of hot spots and stress concentration zones, and adjust the overflow size and position digitally. This cuts the number of mold modification cycles and saves trial-out scrap cost.
4. Zoned Die Temperature Control and Shot Profile Tuning
Uniform mold temperature is impossible for large battery tray molds. The design adopts graded zoned cooling and heating control for the die cavity. Thick boss hot spots are equipped with close-range cooling lines to speed up solidification and reduce shrinkage stress. Thin rib areas use mild heating to maintain mold temperature and prevent premature solidification. Independent mold temperature controllers are configured for fixed half and moving half, and different zones run separate temperature parameters.
The shot curve is re-calibrated. Slow shot speed is controlled to push out air inside the shot sleeve stably. Fast shot speed is matched according to the distance from the gate, avoiding excessive impact on the cavity wall. The pressure build-up time is adjusted to ensure that pressure transfers to the hot spot before the alloy completely solidifies. Improper delayed pressure will lead to loose structure and hot tearing.
The release agent spraying program is segmented by robot. Hot thick zones need adequate spraying for cooling and anti-sticking; thin-wall rib areas reduce spray volume to avoid excessive moisture and rapid surface cooling. Improper spraying is often a hidden cause of unstable defect rates in mass production.
5. Online SPC Monitoring and Full-Link Quality Verification
Automotive structural castings require stable quality over long batch production. The project built an SPC online monitoring system to record shot parameters, mold temperature, vacuum pressure and cavity curve for every cycle. The system triggers automatic alarms once parameters deviate from the tolerance window, preventing large batches of defective products.
The quality inspection gate is set as: first visual check for surface cracks and cold shut → UT inspection sampling for hot tearing risk zones → CMM dimensional measurement for sealing flange flatness → fixture check for overall warpage trend. Test data is tracked continuously to observe the trend of deformation drift.
Mold maintenance rules are formulated according to shot count. The cavity surface is regularly polished to remove soldering accumulation. Surface coating such as AlCrN PVD is applied on high-wear gate and overflow areas to extend mold service life and keep stable surface condition. After continuous mass production verification, the hot tearing reject rate drops sharply, and the pass rate of flange flatness reaches 97.5%. The solution successfully passed PPAP audit for a mainstream new energy OEM.
Conclusion
This integrated high-pressure die casting solution for EV aluminum battery trays proves that controlling hot tearing and warpage of large thin-wall castings is a systematic project. It relies on optimized alloy formula, well-designed gating system, zoned die temperature regulation, precise shot control and continuous SPC quality tracking. As battery packs trend toward larger integrated cast structures, the ability to stably produce large aluminum tray castings with low residual stress and high dimensional consistency will become a core competitive advantage for die casting enterprises serving the new energy automotive supply chain.
Get the latest price? We'll respond as soon as possible(within 12 hours)